Geotechnical instrumentation is a critical part of every construction project as it provides vital information about the in-situ behavior of the ground. Instrumentation methods highly depend on the substratum and groundwater conditions. The instruments utilized are also impacted by the design methods and the compatibility of a project.
Slope inclinometers are devices developed to monitor and measure the deformation of the subsurface. They have been widely used since the 1950s to evaluate the performance of natural slopes, embankments and retaining walls providing significant data about in-situ ground movements that could be an indicator of potential failures.
Inclinometers were initially utilized to monitor landslide deformations and assess slope instabilities. Nevertheless, they are currently used to evaluate more complex interactions such as the effect of excavations on nearby structures, deformations of buildings and settlements of embankments and roadways.More specifically, the installation of slope inclinometers serves the following scopes:
A typical inclinometer consists of 3 parts: i) a probe, ii) a readout device, and iii) a cable. A casing is also used to drive the probe into position and to protect the device from soil and water penetration.
The probe is composed of at least one force-balanced accelerometer that measures the inclination of the casing with respect to the vertical direction. The commonly utilized inclinometers contain two accelerometers and use a biaxial probe.
Two wheels that enable the device to move within certain grooves in the casing are attached to the probe at a fixed relative distance (0.5 meters). One accelerometer is placed parallel while the other is placed perpendicular to the wheels. The accelerometers measure the tilt of the casing with respect to the vertical direction in both horizontal directions. The layout of a typical probe inclinometer along with the inserted wheels and the directions of measurements (A- and B- axes) is depicted in Figure 1.
The cable is attached to both the probe and the readout device and its role is twofold:
The readout device records the inclinometer’s measurements and is capable of storing data. It is equipped with a rechargeable power supply.
Data accumulation, editing and management are conducted via a computer software. The sensors may also collect data concerning precipitation rates, groundwater level or temperature that can be associated with the results of the test.
Various types of slope inclinometer and their components are presented in Figures 2.
Vertical slope inclinometers are installed within boreholes which are shafts relatively small in diameter bored in the ground. The borehole should be large enough to accommodate the device’s casing and a pipe from which grout will be inserted.
Segments of the casing are placed in the borehole until the desired depth. The casing must be installed 3-6 meters deeper from the point where displacements are expected to be eliminated.
Two grooves are then installed carefully in order not to apply too much torque on the casing.
The guide grooves must be kept clean via water hosing or brushing during the installation so that tracking problems will not emerge.
Grout, a mixture of water, Portland cement and bentonite, is pumped through the pipe and into the borehole. The purpose of using grout is to bond the slope inclinometer with the surrounding soil.
Once the system is installed, the internal part of the casing must be kept clean so that the probe travels via the grooves without obstructions.
It should be noted that a vertical inclinometer is utilized to derive the horizontal deformation of the ground.
The function of a horizontal slope inclinometer is similar to that of the vertical inclinometers. However, they are installed in horizontal boreholes in which either one or both ends attach to the surface of the ground.
The grooves must be aligned vertically without any twisting and their perpendicularity is verified during the addition of a new casing segment.
Horizontal slope inclinometers are used to derive the vertical movement of the ground.
The inclinometer’s probe is inserted into the casing and its tilt is derived by taking consecutive measurements at every 50 centimeters (the distance between the two wheels inserted). On special occasions, more measurements can be taken in smaller intervals to provide more accurate results.
The reading process begins at the base of the casing. The probe remains inactive for around 10-15 minutes so that its sensors stabilize with the temperature of the ground.
When the test is completed and the probe reaches the surface of the ground, it is rotated by 180 degrees and re-inserted into the casing so that the procedure can be repeated.
The horizontal displacement of the probe is derived via the following equation: S = L * sin(θ)
Where θ is the angle of tilt and L is the measurement interval (usually 0.5 meters as mentioned above).
A schematic of an inclinometer’s configuration is depicted in Figure 3.
If the base of the inclinometer casing is considered stable, tilt data from the bottom are accumulated to create cumulative results. Otherwise, the top of the casing is considered the reference point.
The accuracy of a typical inclinometer is ±7.6 millimeters per 30 meters but this is highly dependent on the type of the inclinometer. There are systematic errors which affect the reliability of the measurements and include minor faults in the installation of the probe, and random errors that are associated with the function of the sensors.
The ground’s deformation is derived via the cumulative alterations of the casing inclination and at a given depth as shown in Figure 4.
Evaluating the results of an inclinometer test requires engineering judgment to identify errors that could create deformation patterns that do not actually exist.
In the case of a vertical inclinometer, the horizontal ground displacements are derived using a biaxial probe. If the critical direction of movement is parallel to one of the A- or B- axes (Figure 1), the total deformation can be derived using the measured data of the corresponding axis.
Machan, G. and Bennett, V. (2008). Use of Inclinometers for Geotechnical Instrumentation on Transportation Projects: State of the Practice. Transportation research circular.
Looking for Inclinometer Equipment? Fill in the form and we will contact them for you.
Geotechnical Engineering has been - throughout th...
In this 2011 lecture, Dr. Andrew Bond of Geocentr...
Professor Ross W. Boulanger and Professor, Emerit...
The Problem: A 30 m high unstable slope along th...
Looking for Inclinometer Equipment? Fill in the form and we will contact them for you.GET A QUOTE NOW